• Parameter Setting of Siemens S7-1200PLC Signal Module
    Parameter Setting of Siemens S7-1200PLC Signal Module Oct 16, 2023
    Address allocation of input/output points Add the DI2/DQ2 signal board, DI8 module, and DQ8 module to the device view of CPU 1214C, and their 1. Q addresses are automatically assigned. After the configuration task is completed, you can use the device overview view to view detailed hardware configuration information. In the device overview view, you can see the byte addresses of the CPU integrated I/O points and signal modules. For example, the byte addresses of the 14 point digital input integrated with CPU 1214C are 0 and 1 (10.0 to I0.7 and I1.0-I1.5), and the byte addresses of the 10 point digital output are 0 and 1 (Q0.0 to Q0.7, Q1.0 and Q1.1). The byte addresses of both DI2/DQ2 signal boards are 4 (14.0-14.1 and Q4.0-Q4.1). The addresses of DI and DQ are allocated in bytes. If all the bits in a byte allocated to them are not used up, the remaining bits cannot be used for other purposes. From the device overview view, you can also see the input and output byte addresses of the signal modules assigned to each slot. Select a module in a slot in the device overview to modify the automatically assigned 1 and Q addresses. It is recommended to use an automatically assigned address and not modify it. However, during programming, the addresses assigned to each IO point during configuration must be used. Parameter settings for CPU integrated digital input points When configuring digital input, first select the CPU or signal board with digital input in the device view or device overview view, and then select "Properties>General>General" in the inspection window. The right window displays general information about the module, such as its model, order number, firmware version number, rack and slot number, and a brief description of the module. Select the CPU or digital input signal board, and then select a channel in the "Properties>General>Digital Input" folder of the inspection window. You can use the selection box to set the delay of the input filter (0.1 μ S-20 ms). You can also enable the rising edge interrupt, falling edge interrupt, and pulse capture functions of each channel using check boxes, as well as set the hardware interrupt organization block (OB) to be called when interrupt events are generated. The pulse capture function temporarily maintains a narrow pulse state of 1 until the next refresh of the input process image. The rising edge interrupt and falling edge interrupt can be enabled simultaneously, but the interrupt and pulse capture functions cannot be enabled simultaneously. Parameter settings for DI modules Select the digital input module in the device view, and then select "Digital Input". You can only set the delay of the input filter in groups (4 points per group) (0.2-12.8 ms) At the beginning of each scan cycle, the CPU reads the status of the external input circuits of the input module and stores them in the process image input table. During the scan cycle, the user program calculates the output values and stores them in the process image output table. At the beginning of the next scan cycle, write the content of the process image output table to the output module. Parameter settings for digital output points Firstly, select the CPU, digital output module, or signal board in the device view or device overview view. After selecting "Digital Output" in the inspection window, you can choose to keep the digital output at the previous value (keep last value) when the CPU enters STOP mode, or use an alternative value. When selecting the latter, select an output channel in the left window and set its replacement value with a check box to ensure that the system enters a safe state when automatically switching to STOP mode due to faults. A '√' in the check box indicates that the alternative value is 1, otherwise it is 0 (the default alternative value). Parameter settings for analog output module Select the 4AI/2AQ module in the device view and set the parameters for analog output. Similar to digital output, it can be set that after the CPU enters the STOP mode, each analog output point maintains the previous value or uses an alternative value. When selecting the latter, alternative values for each point should be set. The output type (voltage or current) and output range of each output point need to be set. It can activate the short circuit diagnosis function for voltage output, the open circuit diagnosis function for current output, and the overflow diagnosis function for exceeding or below the upper limit value. The parameter setting methods for the CPU integrated analog output point, analog output signal board, and analog output module are basically the same.

Need Help? Chat with us

leave a message
For any request of information or technical support, fill in the form. All fields marked with an asterisk* are required.
Looking for FAQs?
Contact us #
+86 -15259245292

Our hours

Mon 11/21 - Wed 11/23: 9 AM - 8 PM
Thu 11/24: closed - Happy Thanksgiving!
Fri 11/25: 8 AM - 10 PM
Sat 11/26 - Sun 11/27: 10 AM - 9 PM
(all hours are Eastern Time)




Contacts Us